I need some info...

I've got the 02 sensor mod fitted and have a spanking new fuel mod sitting on the shelf in my garage...

Can I fit the fuel mod without the stage 1 & 2 DNA filters ?

Is there any point?

Will it make a difference or should I wait for my filters.

Thing is I am getting impatient and want to fit it but can't afford the filters for a while.....

Cheers guys.

I know I should have asked kev but I have asked him so many questions so far that I reckon he might think I'm slightly mental....so Sshhhhh don't tell him I asked...

You may as well fit it. Nothing to loose and it'll keep you busy for the time being!

Set it to 3 o'clock with the stock filter and go to around 5-6 o'clock when you've got the DNA bits fitted.

__________________

Great one thanks, I'll give it a shot....

Any tips on getting it just in the right position for my bike ?

Is it a case of adjust and ride adjust and ride or shall I do a plug chop ?

As I said, start at a ball-park 3 o'clock with stock filter. Then you'll need to up the resistance once you have the DNA stage 1-2 fitted.

I found best way to get the setting right is to hang the control out the side of the seat and go for a ride, fiddling with the setting as you go. Try changing the setting at various throttle positions, engine speeds and loads. Make sure motor is up to full operating temperature before you make changes. Experiment and see where you end up.

__________________

Set the fuel mod as instructed in the Fuel mod instructions & you will be fine.

__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946

Plz, Let us know the results without the DNA filters.
Thanks!

Sent from my GT-I9100 using Tapatalk 4

__________________


RTW from London to Australia - May 2014 - http://www.hebbortw.com

hi all.

ok I fitted the fuel mod without the filters and BAM!!!! Another huge change to the bike and the way it went. I set the dial at 3 I clock and the difference was trully amazing.

power was delivered much smoother completely done away with any surging and she pulls hard from very low down now.

input the dial to 4 and it was not as good so dropped it back to about 3:15 (3 and a tiny bit) as I'd cut snorkel down.

better much much better.

so to sum up I have:

02 sensor mod
fuel mod
cut down snorkel
standard filters
standard exhaust with cat still in.

I'm fitting a single stainless MTC tomorrow. will report back.

Hi Gibbo yes saw that can for sale on the bay, let us know how you get on please.
Stephen

Hi mate, see thread above this, title is OMG it's LOUD.....you can guess how the noise test went...lol