I've been searching, but can't seem to find any threads on risers for the new Teneres.

What do you guys reckon? Are there any commonly agreed upon bar risers that are best for the new 660z Tenere? Anything to be aware of with fitting them?

The standard ones just seem too low when I'm standing up.

Try this thread...

http://www.xt660.com/showthread.php?t=18881

Most info is covered here.

Main thing to watch is cable length if you go more than +30mm

__________________

i've got some shim stack style ones that cost about �35, there good as you can alter the height.

I had them at full height to start with which was 40mm, cables reached and when up on the pegs the bars felt at a great height. But....its all a compromise, as when sat down the bars felt too high.

I've took a shim out so now there at about 30mm whcih feels good when stood up or sat down.

The main problem is when you have an off, the risers seem to twist. You need to loosen it all off, re-align and tighten up. Not hard to do but just annoying.

It's because the risers are mounted in rubber bushes in the top yoke.

TBH when I had the stock front end in I never found I needed to loosen anything off, I could usually straighten it up sat on the bike just by forcing the bars against the lockstops.


Rather than using extra risers, another option is to change the bars for Renthal 613 bend. Gives about 25-30mm raise at the grips, and works with the stock cables.

__________________
I spent a lot of money on travel and racing motorcycles - the rest I just squandered.

XT660Z - Commuter, Adventurer...Racer?

www.dashmoto.net

Other bikes >> MT-03 / CG125BR-J / ER-6F
Departed >> ZXR400L3 / EC300 / DR-Z400E / DR800S / GPZ500S / GS400

i was going to put up a post asking about this. I'm going to change from stock bars over the winter (mine are bent) and wondered about getting some higher bars where i dont have to bother with risers.

are these bars braced?

Yeah, normal 7/8" braced Renthals.

You'll lose your bar end weights and the OE handguards if you have them, but you'll gain the ability to fit better aftermarket handguards.

__________________
I spent a lot of money on travel and racing motorcycles - the rest I just squandered.

XT660Z - Commuter, Adventurer...Racer?

www.dashmoto.net

Other bikes >> MT-03 / CG125BR-J / ER-6F
Departed >> ZXR400L3 / EC300 / DR-Z400E / DR800S / GPZ500S / GS400

I managed to bend the OE bars, and went for the 613 as a replacement. Maybe I just set the rotation of the bars differently, but they have a much more natural feel than the OE bars, and as UT says, no need for risers.

You do need to re-route the throttle cables where they pass under the tank (they go under the oil pipe and need to go over it), like in the graphic below ->




The current route is shown in red, the green is the oil pipe and the blue dashed line is the new route.

__________________
>-------<

Never underestimate the power of stupid people in large groups.

Wow guys, I certainly came to the right place for intel. Thanks for all your inputs. Time to digest & consider now. I do like the simplicity of the Renthal option. I'll let you know how I get on. Cheers guys.

Rox make one of the best...

Attached Images

KT250%20003%20small.jpg (75.7 KB, 55 views)

__________________
Harley Davidson..
The easyest way to turn gasoline into noise with out the side efect of horse power...

Ive just fitted some 15 mm risers off ebay and lift it just nice. My main problem Im thinking is the bend of standard bars, where I seem to like them I feel as if my wrists are turned inwards and my elbows go out. My prefered bar has always been Renthal 613s so may go with them when I get some funds.
If some of you feel the rubber inserts in the top yoke cause twisting, you may be able to go with the same things I used on my older 4MY 660 from Kedo in Germany... plastic inserts that do away with twisting bars