hi,i need to make 20000 km service to my xt660r,for valve adjustment, do i need remove the radiator? (and to empty the wather).

thanke.

No you don't.

All you need to do is unbolt the radiator & let it hang on the water hoses, giving you clearance to set the exhaust tappets.

__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946

Kev is there any tips you can give to do valve adjustments?

I have done cheap cush drive mod and it's was easy, but the valves scares me a bit.

if memory serves me right, they're the sort of tappets where you have the tappet screwed into the rocker and then a locking nut on top?

If so, a couple of good pieces of advice I would have to give is, for a start make sure the piston is in the correct part of the cycle before taking measurements, so that the rockers are at their most loose i.e. checking for TDC.

Another, when tightening the lock nuts after making your adjustments, be sure to hold another spanner on the top of the tappet itself because as you tighten the locknut, its likely the tappet will want to turn with it loosing your adjustment.

Currently, they're main ones I can think of, I'm sure Kev will improve on this further though.

__________________
09 XT660X:

CCC Stainless Rounds, Stage 1 DNA, Stage 2 DNA, PCV With Custom Autotune Map, PCV AutoTune, Home made O2 eliminator, Self machined Fork Spacers, DIY Autotune Switch.

Intake clearance is 0.09-0.13mm
Exhaust clearance is 0.16-0.20mm


I never actually looked or taken any notice as its not due but I'm presuming the Z is a 4 valve. If so use two feelers to get it spot on as the gear has play in it. Using two it takes up any play once one is correctly adjusted. I used to do this on my GS and they resulted in spot on results

__________________
Previous bikes:TS50 - RD125LC - XT250 - ZXR750L3 - BMW 650 Funduro - BMW 1100GS - XT660Z Tenere

X, R & Z all have the same motor.

There should be no play at all between the rocker & it's shaft, if there is then they need to be replaced.

__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946