Hi all, just tried to start my baby after 4 weeks of bone idleness and she wont fire up. The starter dosnt turn over and a clicking noise comes from the box attached to the back of the main fuse. There is no faulty engine light but the display shows Error_01. Its a 04 xtx. Does anyone have any ideas as to what mighe be my problem ????

flat battery is my bet.



Error Codes

Error Number 11 : Cylinder identification sensor error - DIAG mode (none)
Error Number 12 : Crankshaft posiiton sensor error - DIAG mode (none)
Error Number 13 : Air intake pressure sensor error - DIAG mode 03
Error Number 14 : Air intake duct error - DIAG mode 03
Error Number 15 : Throttle position sensor error - DIAG mode 01
Error Number 19 : Sidestand sensor error - DIAG mode 20
Error Number 20 : Air pressure sensors error - DIAG mode (none)
Error Number 21 : Coolant temperature sensor error - DIAG mode 06
Error Number 22 : Air intake temperature sensor error - DIAG mode 05
Error Number 23 : Ambient air pressure sensor error - DIAG mode 02
Error Number 24 : O2 (lambda) sensor error - DIAG mode (none)
Error Number 30 : The bike went down - DIAG mode 08
Error Number 33 : Coil 1 open circuit - DIAG mode 30
Error Number 34 : Coil 2 open circuit - DIAG mode 31
Error Number 41 : Tilt sensor error - DIAG mode 08
Error Number 42 : Speed sensor error / Neutral sensor in short-circuit - DIAG mode 07-21
Error Number 43 : Battery voltage control error - DIAG mode (none)
Error Number 44 : EEPROM read/write error - DIAG mode 60
Error Number 50 : ECU memory error - DIAG mode (none)
Error Er-1 : ECU link error
Error Er-2 : ECU link error
Error Er-3 : ECU link error
Error Er-4 : ECU link error

Following ERROR codes DO NOT allow engine to run :
11-12-19-30-41-50 and Er-1 to Er-4
Error code 11 allow engine to continue running only if fault appears after engine start.

Following ERROR codes DO allow engine to run but need immediate check because default values are taken by the ECU: 13-14-20-21-22-23-24-24-42-43-44

Yep - flat battery.

__________________
My Mods | TLC | A good spannering | Kev's brilliant Mods & advice via XTSupporters - Best �10 ever spent.Lucid Puppy && SeaMonkey - Wubi - - Boinc - electric sheep

XT Modifications - XT Supporter's scheme

Thanks guys. I got it charging so hope for the best. I had problems earlier this summer with dodgy electrical connectors on the wiring loom, lots of weird stuff happening like losing my headlight at 80mph at night, brake light only working when it felt like it etc..
When i got it there was only 3 indicators on it so i bought a nice sexy set of LED mini blinkers but when I fitted em they will only flash twice as fast as normal but the hazzards work fine ??
Are electrical problems par for the course with the XTs or do I own a pup ??

When you fit led's you need a gizmo which I can't remember the name of, that you can get that in most bike shops that sells Oxford products. its like a tiny chip with wires that you connect in between the indicators... box.. help anyone?

LED winkers need a resistor to make them work at the correct rate or make your own (click on Kev)

Kev

Sounds like you need to go over all the connections/earth points and clean them and add electrical battery grease to preserve.

__________________
My Mods | TLC | A good spannering | Kev's brilliant Mods & advice via XTSupporters - Best �10 ever spent.Lucid Puppy && SeaMonkey - Wubi - - Boinc - electric sheep

XT Modifications - XT Supporter's scheme

Thanks lads, flat battery was the first problem and it looks like I need to buy some resistors. I kept the standard indicators on the front so will 2 resistors on the back do me or do I need to change the front ones to LEds too?