Home

Go Back   .: XT660.com - The #1 XT660 Resource :. > XT660 Community > Newbies Reception Lounge
FAQ Calendar Search Today's Posts Mark Forums Read Main site

Google

Newbies Reception Lounge Newbie introduction forum, just say hi and show us your bike, tell us where you're from and how you've found us, and see how many will welcome you aboard!!

Reply
 
Thread Tools Display Modes
  # 11  
Old 23-03-12, 20:28
maxwell123455 maxwell123455 is offline
XT-Moto SuperStar
 
Join Date: Jul 2007
Location: Edinburgh, Scotland
Posts: 1,943
maxwell123455 is on a distinguished road
Hi and welcome to the forum

The chain and sprocket change isnt too hard. As other have said make sure to get a good set of tools, take your time, take photos every time you take something off so you can remember what way it goes back on.

If no one gets in touch your local dealer should be able to allow you to sit in on the changing of the change and sprockets allowing you to make notes, ask questions and find out how its done and pitch in, meaning when you go to do it on your own next time you have tools and the no how how to do it
__________________
Plough on
Sponsored Links
  # 12  
Old 24-03-12, 04:14
Camels Camels is offline
Newbie XT-Moto
 
Join Date: Mar 2012
Location: Lane Cove North, NSW, AUS
Posts: 5
Camels is on a distinguished road
Elaboration

Hi everyone, thank you for all your responses.

I was just asked about the finer details of why I need to change the drive train, which has prompted me to elaborate to you all. The sprockets are both badly damaged and have torn into the chain. I recently stretched the chain out as far back as the rear axel would go. On Wednesday, I had just left Uni and was riding into the Macquarie Centre car park and the rear wheel locked up and I skidded to a halt (thankfully I was travelling at less than 20kmh). The chain had worked its way loose, came off and wrapped up the rear axel. I unsnagged the chain and rolled the bike into the car park, I then got NRMA to tow it back to my apartment garage where it now sits in the visitors parking.

I would love to get a Haynes guide and get to work in a well set up home workshop but one of the biggest issues is that I have no tools. I don�t even know which tools to get so I sort of want to see them in action and get a feel for what I want in each tool before I start buying up.

I�ve just moved to Sydney to study full-time and encountered a lot of costs associated with the move. I can�t afford to be buying tools which I may not need or find to not be suitable. I don�t even have the tool kit which would have come with a new bike. I know that sometimes you buy a tool then a month later realise that you wish you had bought the slightly different variation instead. So basically, the cheaper option is to just take it to a workshop and get someone else to do it all. (I�ve found that workshops don�t let me in to see what they are doing due to OHS/WHNS)

I�ve accepted that I won�t have the bike fixed this weekend.

So in a broader time frame, what do you all suggest?

Thank you,
Nick Kamols (Camels)
  # 13  
Old 24-03-12, 08:00
Tony660x's Avatar
Tony660x Tony660x is offline
XT-Moto SuperStar
 
Join Date: Oct 2006
Location: Staffordshire, UK
Posts: 569
Tony660x is on a distinguished road
Camels, chain and sprockets is a simple job to do if you know what you are doing, you clearly do not know how to do it or even own the tools. Simple answer, get it to a local garage and get them to supply and fit.

Its a vital area of the bike. The chain falling off is a very serious thing and chances are you have not adjusted it properly either.

If I were local to you I would pop round with all my tools to show you but I am in the UK. Get it sorted mate.

Ride safe.
__________________
  # 14  
Old 24-03-12, 10:14
Woottonboy Woottonboy is offline
Guest
 
Join Date: Mar 2010
Location: Wootton
Posts: 177
Woottonboy is on a distinguished road
Solutions R Us

Further to today's conversation.

Minimum tools needed are going to be:

flat blade screw driver
14 mm ring spanner
5 mm Allen key
Chain breaker (one that can re pin as well)
socket (can't remember size) and torque wrench
22 and 24mm spanners to remove rear wheel
10mm spanners to adjust axle

Consumable list:
front sprocket
rear sprocket
chain and joiner link
2 man job, therefore at least one cold beer for mate.

If your that short of cash, I can lend you a new 14 tooth sprocket until you can pay for it or you can have my old 15 tooth unit that's still good but you'll have to get on a train to Granville tomorrow to collect. At least that way you'll only have to find the cash for a chain and rear sprocket and pay for install (at most $200).

BUT
By the sounds of it 32,000 km and deeply hooked sprockets and a chain stretched to ******y&back you really must replace the lot. On ebay you can buy a set for around $150 I suggest you do. Tools are going to be another issue all together and if I wasn't off to family court on Monday to try to get my girls for Christmas time I'd bring everything and lend a hand, I really would. Unfortunately your going to have to push it there.

Just remember: That what doesn't kill us makes us stronger.

Only 2km, take water think positive.

Now the controversial comment.

Since the chain is no good, I'd be tempted to take out a pair of links, and that should get it back to adjustable length (one pair is 32mm) surprise surprise axle adjustment is 35mm. It will only cost about $50 - $80 to buy a chain breaker but get a good one (that re pins as well). Restrict your riding to bare minimum and easy on the go fast, your sprockets will eventually let the chain ride over the teeth and you definitely don't want that. You might get another month or two. It would be better not too.

But we've all be broke and I guess your going to have to sort it out somehow.

Last edited by Woottonboy; 25-03-12 at 08:21. Reason: changed (=) sign to a (-) sign
  # 15  
Old 26-03-12, 04:49
boneman boneman is offline
Expert XT-Moto
 
Join Date: Jun 2011
Location: Queensland
Posts: 169
boneman is on a distinguished road
help is at hand

Nick, check over at ADVrider forum under the Australian regional forum. There are offers of help for you in Sydney. Thread title "help needed for NOOB in Sydney." Good luck...
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 04:44.
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.

  XT660         Archive   Main site


Footer
vBSkinworks Top