Hello,

any of my fellow Ten riders had any issues after doing a washing of the bike?
Today I had this strange problem after cleaning my bike. Turned the key as usual, the bike did the fancy light tricks but when pressing the start button, the bike didn't want to start! After a few seconds I just pulled some throttle and the bike came to life.
I just didn't like the smoke that came from the front cable and the smell of burned rubber.
Should this be cause for concern?

I always use a pressure washer to clean the bike and have never had any issues when starting it.
I would always be concerned about the smell of burnt rubber!!!!!
Have you checked for any obvious damage to cables / connectors?

__________________
Work hard, rock hard, eat hard, sleep hard, grow big an wear glasses if you need em.

Does not sound good at all. I would inspect the smoking area & find out where the burning smell came from.

__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946

Which "front cable" was it??

Yes, if you've confused burnt rubber with burn plastic, then it is almost certain something shorted out in the wiring and melted... have you checked to see if all the other electrical circuits are working, and any fuses blown?

Jx

__________________
"Where we're going, we don't need roads..."

JennyDakar.com

I've made a search on all the front cables but couldn't find any burned wires, rubber or plastic. I haven't checked the fuses yet, but i've tested all the lights and everything is working normally.

Let's just hope the bike won't fail me in the middle of nowhere.

Thanks for your help.