Home

Go Back   .: XT660.com - The #1 XT660 Resource :. > XT660 Tech Section > Performance Modifications & Enhancements > Fuelling and Intake
FAQ Calendar Search Today's Posts Mark Forums Read Main site

Google

Reply
 
Thread Tools Display Modes
  # 1  
Old 21-08-10, 17:11
dazmatic dazmatic is offline
XT-Moto SuperStar
 
Join Date: Jul 2009
Location: leiston
Posts: 358
dazmatic is on a distinguished road
O2 sensor eliminator mod (By Kev with the help of dazmatic)

Note: Jump to latest (2012 on) plug 'n' play version here

Well, I've finally got a working version fitted onto my bike this morning and tested it whilst sitting on my driveway. Initial indications suggest that it works as well as expected if not better and would appear to not interfere with the running of the bike and was actually a lot easier to install than I first imagined it would be which is also good.

I did however go for a ride to get some shopping and well...

WoW

No surging or bucking, bike rides a lot lot more smoother now.
Was an absolute dream to ride!

It produced a good map which I thought I'd saved to my PC but hadn't! I now can't be arsed to go back out again and setup my laptop to read it but will do it tomorrow or something.
But I assure you, it looked good.

A few pics of it in place. Be aware though, this is just a prototype. Hopefully the next one will be pukka!

Mod in its location whilst installing.



Sensor



Live feed to the mod taken from the loom, from the same place where the live feed for the PCV is taken from. Wrapped in special electrical wrapping tape (not that nasty sticky tape!)



PCV Under the tail section with wire for analogue feed (PCV can now tell the engine temperature!) and my Autotune Switch and Autotune just to the right.



The finished prototype installed under the seat and held down with sticky pads.

__________________
09 XT660X:

CCC Stainless Rounds, Stage 1 DNA, Stage 2 DNA, PCV With Custom Autotune Map, PCV AutoTune, Home made O2 eliminator, Self machined Fork Spacers, DIY Autotune Switch.

Last edited by Pleiades; 27-01-15 at 21:46. Reason: add link to latest version
  # 2  
Old 21-08-10, 17:21
Paul Curtis Paul Curtis is offline
Expert XT-Moto
 
Join Date: Mar 2008
Location: North Linconshire
Posts: 146
Paul Curtis is on a distinguished road
Looks good but will this mod only work with a PC5 or will it work with a PC3
__________________
my mods
2008 XTX/C.C.C. stubies/D.N.A.stage 3 Air filter/PC3+Custom Kev map/Kev's O2 eliminator mod/yam sump guard painted/yam hand gaurds+spoilers/S.W.Moteck engine bars/R&G swingarm protectors/R&G fork protectors/Puig screen/Worry Brother Tail tidy/L.E.D rear light/L.E.D indicators/Personal number plate/Oxford hot grips/Hyperpro front springs/15w fork oil/Hyperpro rear spring/Avon Distanzia tyres/42t rear sprocket/powder coated heal plates and rear foot rests/L.E.D front spot lights
  # 3  
Old 21-08-10, 17:29
dazmatic dazmatic is offline
XT-Moto SuperStar
 
Join Date: Jul 2009
Location: leiston
Posts: 358
dazmatic is on a distinguished road
Unfortunately, I cannot make any promises yet.

However, I don't see why not so long as there is a bit of dyno time involved.

I don't have a dyno near me hence why I used a PCV with autotune. Not to mention I can mod my bike and be able to remap with that new mod.

All this mod does is keep the bike in open loop mode so that the entire rev range can be mapped.

No more 'Cannot map at 20% throttle between X and X rpm'

Bare in mind, this mod is only for bikes that have an O2 sensor, so 2007 - 2009 I believe? Something like that anyway...
__________________
09 XT660X:

CCC Stainless Rounds, Stage 1 DNA, Stage 2 DNA, PCV With Custom Autotune Map, PCV AutoTune, Home made O2 eliminator, Self machined Fork Spacers, DIY Autotune Switch.
  # 4  
Old 21-08-10, 19:19
richardsracingmad richardsracingmad is offline
XT-Moto SuperStar
 
Join Date: Jul 2010
Location: the South
Posts: 875
richardsracingmad is on a distinguished road
nice one Daz....if one arrives in time for my Dyno, we can test it!
  # 5  
Old 21-08-10, 21:03
dazmatic dazmatic is offline
XT-Moto SuperStar
 
Join Date: Jul 2009
Location: leiston
Posts: 358
dazmatic is on a distinguished road
Haha...

I know it will work, Kev and I have proven that.

But thats not the thing that needs testing really, however, I can't say as of yet what is.
I'm sure it works, but just need to be doubley trippley sure of it.

The real thing is, putting together something that can be distributed.
I need to compile a shopping list of bits and create a design that can just be wired up easily straight out of the box and be of good enough quality too.

As you can see, what I've made here is (I think) rather crude and if I do decide to make more would like to make something of a better standard.

I know of a design that I would like to use and need to trial it first but that requires cash, something which I don't have a lot of at the moment so may have to wait till I can afford to develop this a bit further.
__________________
09 XT660X:

CCC Stainless Rounds, Stage 1 DNA, Stage 2 DNA, PCV With Custom Autotune Map, PCV AutoTune, Home made O2 eliminator, Self machined Fork Spacers, DIY Autotune Switch.
  # 6  
Old 22-08-10, 00:04
Kev's Avatar
Kev Kev is offline
Administrator
 
Join Date: May 2006
Location: Brisbane, Australia
Posts: 6,063
Kev is on a distinguished road
This is a joint venture between Dazmatic & myself.

As I mentioned before I found a way to turn off the the O2 sensor on our XT's a few months ago & could prove that it worked by looking at the air fuel ratio while riding. I made up the mod using relays & temp switch's which was to complicated for the average person to wire up, I asked for help & enlisted dazmatic to help me make an electronic version that was easier to wire up.

Dazmatic has done well, the mod will need to be tested for a while before we can say it is a reliable working mod. We will need to build special fuel maps for the PCIII & PCV to go with this mod.

Yes it should work on any XT660 with a O2 sensor, but you will need a PCV or PCIII for this mod to work, as a new fuel map will need to be made.

The proof.

The surge before.
http://www.youtube.com/watch?v=ZwTfuwZZ848&feature=channel

The O2 sensor turned off.
http://www.youtube.com/watch?v=1Y9mqJtXtm4&feature=channel
__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946


Last edited by Kev; 22-08-10 at 06:35.
  # 7  
Old 24-08-10, 21:56
nazurro nazurro is offline
Expert XT-Moto
 
Join Date: Aug 2009
Location: Link�ping
Posts: 61
nazurro is on a distinguished road
Quote:
Originally Posted by dazmatic View Post
Well, I've finally got a working version fitted onto my bike this morning ...
Wow, great stuff!

I will definitely be interested eventually, as soon as I get myself a PCIII.
  # 8  
Old 10-09-10, 00:39
Paul Curtis Paul Curtis is offline
Expert XT-Moto
 
Join Date: Mar 2008
Location: North Linconshire
Posts: 146
Paul Curtis is on a distinguished road
Any news on the eliminator yet please ??
__________________
my mods
2008 XTX/C.C.C. stubies/D.N.A.stage 3 Air filter/PC3+Custom Kev map/Kev's O2 eliminator mod/yam sump guard painted/yam hand gaurds+spoilers/S.W.Moteck engine bars/R&G swingarm protectors/R&G fork protectors/Puig screen/Worry Brother Tail tidy/L.E.D rear light/L.E.D indicators/Personal number plate/Oxford hot grips/Hyperpro front springs/15w fork oil/Hyperpro rear spring/Avon Distanzia tyres/42t rear sprocket/powder coated heal plates and rear foot rests/L.E.D front spot lights
  # 9  
Old 10-09-10, 02:09
Kev's Avatar
Kev Kev is offline
Administrator
 
Join Date: May 2006
Location: Brisbane, Australia
Posts: 6,063
Kev is on a distinguished road
Will be on my bike tomorrow & tested on the dyno on the 27th. We are still working on a better way to run the fans.

Dynojets Emulator is close hopefully, as some of the UK's dynojet dealers have been given the pricing on the Emulator.
__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946

  # 10  
Old 10-09-10, 08:38
Paul Curtis Paul Curtis is offline
Expert XT-Moto
 
Join Date: Mar 2008
Location: North Linconshire
Posts: 146
Paul Curtis is on a distinguished road
Thanks Kev thats good news
__________________
my mods
2008 XTX/C.C.C. stubies/D.N.A.stage 3 Air filter/PC3+Custom Kev map/Kev's O2 eliminator mod/yam sump guard painted/yam hand gaurds+spoilers/S.W.Moteck engine bars/R&G swingarm protectors/R&G fork protectors/Puig screen/Worry Brother Tail tidy/L.E.D rear light/L.E.D indicators/Personal number plate/Oxford hot grips/Hyperpro front springs/15w fork oil/Hyperpro rear spring/Avon Distanzia tyres/42t rear sprocket/powder coated heal plates and rear foot rests/L.E.D front spot lights
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 20:59.
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.

  XT660         Archive   Main site


Footer
vBSkinworks Top