Hi Guys,

not sure if any of you can help, but I'm getting a regular problem of my engine cutting out on me.

Bikes only done 1300 miles, and every now and then the engine cuts out while I have the clutch pulled in.

It always happens at very low speeds, mainly if I'm filtering in traffic, and pull the clutch in. If if blip the throttle the engine makes a click and cuts off. It starts up again right away, in fact, each time I've been able to restart without interrupting the movement, but is a little worrying. Happened about 5 times so far always under the same conditions.

I'll be taking it back to the dealer soon to check it out, but just thought I'd see if anyone has any ideas so I can go in a little more educated?

Bike is completely standard, oil level good.

Any ideas?

thanks in advance.

JD

this happend on my xt and i checked the tps position and increased the rpm to 1500 but would not of thought you would be doing this on a 2010 xt thats only done 1300 miles.

My 2006 XTX used to do this, usually when going down the box approaching a junction / roundabout. Was very unpredicatable, might do it a couple of times in close succession and then not again for ages. Just got used to it and dipped the clutch and started her again. Happily it's gone away now that i have MTC cans / PCIII / Stage 1 & 2 filters. I know it's been posted about before and is not uncommon.

Not that any of that babbling is of any help to you.... hopefully a grown up with useful advice will be along soon

SelinaXT

Set your idle speed to 1500 rpm, can you remove your left black side cover & give me your full ECU part number, it should end with -11.

__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946

Cheers guys, I'll give all those a try. Kev, think we already discussed the ECU in another thread, but its the 2009 part number that ends in -11.

I'll have a fiddle with the idle speed at the weekend and see if that sorts it. Not a major problem though, just a little annoying. It never happens at a decent speed, only when trickling.

Good excuse for me to start modding a little I guess

Of course it is. Its never too soon as long as the funds are there.

__________________
Mods so far:- Kev Mod/Snorkel Removed/Airbox Drilled/CO2 Upped/Cush Drive Mod/M.T.C. Exhaust/Avon Distanzias:avon: Fitted/NGK Iridium Spark Plug/H4 Bulb Upgrade/White Wheel Trim/Scotoiler/Hand Guards.

No worries mate, I help so many guys out I loose track of every bodies bikes. I also have 100 customer problems a day to deal with at work everyday as well. Mmmm I need more memory.

__________________
Click here to join the XT Supporter's scheme

Mods that I have done to my XTX's

My 04 XTX
Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil /
[
My 07 XTX
Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator /

My 09 XTX
59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details

Now ride a 2018 MT09SP ABS + TCS

My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946

Upped the idle speed today so it bounces nicely around the 1500 mark. Bike rides a lot better there for a start, and so far no cut outs. Thanks for the help guys, I'll keep an eye on it and let you know if it happens again.

I think I better become a supporter. I feel bad leaching info from you all without being able to give back.

http://www.span.com/product_info.php...k&currency=GBP

Plenty of memory there!

__________________
09 XT660X:

CCC Stainless Rounds, Stage 1 DNA, Stage 2 DNA, PCV With Custom Autotune Map, PCV AutoTune, Home made O2 eliminator, Self machined Fork Spacers, DIY Autotune Switch.