|
|
|
|
|
|
|
|
#
1
 20-02-10, 23:34
|
|||
|
|||
|
Fitting a Power commander.
After some advice on power commanders please.
Never had one on bike's i've had in the past so.... The PCv? Does it just plug into the loom of the Tenere? Do you have to block the AIS with a PCv fitted? Do you need to mess with the exhaust sensor? Will it come with any maps loaded or will it be set as standard so a map will be needed? Many thanks all 
|
|
#
2
26-02-10, 22:15
|
|||
|
|||
|
Hi!!
Quote:
__________________
09 XT660X: CCC Stainless Rounds, Stage 1 DNA, Stage 2 DNA, PCV With Custom Autotune Map, PCV AutoTune, Home made O2 eliminator, Self machined Fork Spacers, DIY Autotune Switch. |
|
#
3
27-02-10, 00:08
|
||||
|
||||
|
[quote=banksy;120818]After some advice on power commanders please.
Never had one on bike's i've had in the past so.... The PCv? Does it just plug into the loom of the Tenere? Plugs into the injector, TPS & a earth wire to the battery. Do you have to block the AIS with a PCv fitted? Only if you want to stop the poping, or making a custom fuel map on the dyno or you have a Auto Tune from Dyno Jet Do you need to mess with the exhaust sensor? Not on the XTZ they seem to run quite fine with the O2 sensor connected with a fuelling device. If you disconnect the O2 sensor you must remove the O2 sensor otherwise it will clog up over time & will not work when you come to use it again one day. Will it come with any maps loaded or will it be set as standard so a map will be needed? If you buy from Simon he will load the correct map for your set up. Many thanks all
__________________
Click here to join the XT Supporter's scheme Mods that I have done to my XTX's My 04 XTX Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil / [ My 07 XTX Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator / My 09 XTX 59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details Now ride a 2018 MT09SP ABS + TCS My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946 
Last edited by Kev; 01-03-10 at 09:26. |
|
#
4
01-03-10, 09:16
|
|||
|
|||
|
Thanks for the replys guys!
|
 |
| Thread Tools | |
| Display Modes | |
|
|
|
|
Hybrid Mode
