.: XT660.com - The #1 XT660 Resource :.

Page 3 of 4

Show 40 post(s) from this thread on one page

.: XT660.com - The #1 XT660 Resource :. ( https://www.xt660.com/index.php)

- XT660Z Mods ( https://www.xt660.com/forumdisplay.php?f=165)

- - Tenere Light Brackets ( https://www.xt660.com/showthread.php?t=21638)

sweller

03-12-13 22:00

I'd be interested in a set of brackets too - I'd also be interested in what are considered best value lights to fit to them.

SimonRoma

04-12-13 10:53

I bought a set of GIVI lights and they were only about 100 Euros, but I was planning to fit the GIVI engine bars to hold the lights. Your solution is a great one but I dont wanna change the mirrors. Any other solution?????

penfold

15-12-13 00:05

Hi,

Noob to the forum and the bike, but I'd be interested in a set if you're still looking to produce them. Nearly forgot, advice on lights would be good too.

Thanks,
Penfold
Lake District, UK

Mirador

17-06-15 11:35

Tenere Light Brackets

I like the look of your light brackets. I live in Australia and ride often at night through eucalyptus forests that are full of kangaroos. These animals are stupid and run out of the bush straight at the bike and the standard headlight on the Tenere is less than perfect for spotting Skippy. Are you still making your brackets and if so will you sell me a set so I can install some LED aux lights? I have been getting ideas from this forum for quite some time now and find your ideas and conversations most helpful.

darkhelmet

17-06-15 11:49

I might be interested too. But i'll have to figure out if the interfere with my WP fork and brakeline that runs along te fork.

Gas_Up_Lets_Go

17-06-15 14:14

Quote:

Originally Posted by Mirador (Post 211667)

Are you still making your brackets and if so will you sell me a set so I can install some LED aux lights?

I've not made any for a few years, but did consider shipping to Aus a while ago. Unfortunately, as they are steel the shipping cost is just daft.

Quote:

Originally Posted by darkhelmet (Post 211668)

I might be interested too. But i'll have to figure out if the interfere with my WP fork and brakeline that runs along te fork.

I don't think they would interfere.

Somewhere I have the plans for them, thy are very very simple if you have access to a welder. The best I can do is to put the plans up and you guys can get your own made up.

I'll take a look tonight

Dukeninja

17-06-15 14:27

Hi mate, are these brackets light-specific or can anything be mounted on them? I realise you haven't made any for some time, but if you have a set lying around I'd gladly take them off your hands.

Cheers!
DN

Mirador

18-06-15 01:55

Quote:

Originally Posted by Gas_Up_Lets_Go (Post 211675)

Somewhere I have the plans for them, thy are very very simple if you have access to a welder. The best I can do is to put the plans up and you guys can get your own made up.

I'll take a look tonight

Being an old farmer I can make anything, in fact if I had not received a reply from you that is exactly what I was going to do, make my own. Your plans will give me the angles and length of pieces saving time and effort. Thanks!

Gas_Up_Lets_Go

18-06-15 09:52

2 Attachment(s)

Here you go, instructions I wrote up a few years ago.

darkhelmet

18-06-15 18:38

Thanks!

All times are GMT +1. The time now is 09:32.

Page 3 of 4

Show 40 post(s) from this thread on one page