![]() |
Engine seized
Hi forum,
So I was riding my bike to a cafe for lunch today when the engine conked out and locked up the back wheel. I was able to control it and pull over but when I tried to start it again I got a horrible scraping noise from the engine and puffs of white smoke from the air filter. I had the bike recovered and the mechanic confirmed the engine needs stripping as something has gone seriously wrong. I am actually 130 miles from home on a 9 day course in Guildford and staying at a hotel so it's a bit of a problem. I checked the oil level before I left on Friday night and it was almost full. I checked it after breaking down and it is just touching the bottom of the dipstick and smells of fuel. It was almost due an oil change so I'm not sure if that is normal or not. What I do know however is that the valve clearances should have been checked 2k miles ago. They were checked when I brought it at 14k miles and it has now done 22k and according to the manual it should be done every 6k miles. Would this have caused such a drastic loss in oil and the engine seizing in less than a week? Thanks, Phil |
Sorry my mistake but actually the valve clearances only need checking every 12k miles so unless the dealer got them wrong they should have been be ok for another 4k miles. Unlikely though as the dealer has a good reputation. Really puzzled as to what caused this.
|
Also nothing seemed wrong prior to the breakdown. Bike sounded and ran as normal until suddenly conking out. No unusual smoke or leaks from anywhere. I rode it for about 10 minutes before it broke down.
Again any input much appreciated. At the moment I am thinking the only affordable option is to replace the engine which is quite frustrating as I know these engines are very reliable and shouldn't have to be replaced after 22k miles of being well maintained. Phil |
Only thing to do is open up the engine and have a look, drain the oil and check it for anything that shouldn't be in there :(
|
Does anyone have any advice on buying a replacement engine or any good sources? My mechanic said it will cost me over a grand for him to strip the engine and repair it so it will be a lot cheaper to replace it myself. At the moment the only ones I can find are on ebay.
Phil Sent from my SM-G900F using Tapatalk |
Drained the oil and other than it smelling of fuel there is no contamination. I tried looking into the spark plug hole and under the rocker cover but cannot see anything from there. When I have time will take the engine out and remove the head. It sounds like the piston rings have gone and they are scraping the barrel.
Are there any guides around for stripping the XT engine? I heard Kev had done one but cannot find it. |
Hi,
I have a good top end from a xt660z which blow the gearbox. let me know if you are interested? Cheers |
Yes I probably would be interested Bonzo thanks. Most likely be needing a cylinder and maybe piston but I need to strip it down first and have a look at what is going on in there before I know, will keep you posted.
|
So I stripped the top end down today and it is all fine. Bummer. Not sure where to go from here. I did find some metal shards in the oil filter so something has broken in the bottom. Any advice on diagnosing the problem anyone? It seems like the teeth on the camchain sprocket are slightly damaged on one side and as it was blowing out of the airbox when I cranked it wondering if it is possible the camchain slipped?
|
Found more large shards of metal stuck to the magneto today when opening the crankcase. My mate reckons the big end bearings have gone, I still have no idea lol. On a brighter note I got the replacement engine fitted and running today. Just need to finish putting the bike back together tomorrow and replace the plastic air pressure sensor for the vacuum pipe as I broke it putting the engine back in the frame. >. < Lucky I found one for �15 on fleabay as Fowlers want �113 + vat for it new! Will strip the bottom end on the old engine when I have the time and a flywheel puller.
Sent from my SM-G900F using Tapatalk |
All times are GMT +1. The time now is 22:51. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.