brake pads
 

Hi

Just wondering what pads you guys are using and do you find the Ten eats rear pads? (yes i know it depends on your riding style...i do a lot of skids :) )

im UK based, will be ording off the net. need rear pads first, any good websites?

Tar very muchly.

Rear pads disappear more rapidly for me too, at a rate of about 2 rears to 1 front.

At the rear I replaced the OE ones (which lasted 9K miles) with EBC pads, cheap at �15, but didn't last as long as OE (about 6K miles) and were a little bit "grabby". The set I'm on now are Brembo (front and rear), which I think are the same as OE and have done 6K miles with about a third of the friction surface left on the back and more than half on the front. The Brembos were exactly twice the price of the EBCs, but a lot less than Yamaha genuine parts.

The EBC pads I got from EBC Direct and the Brembos from Bike Torque Racing

These are the ones I have tried on the Z...

Front EBC FA181TT
Rear EBC FA208TT
Front Brembo 07BB04-12
Rear Brembo 07BB02-40

I've always had good service from Wemoto for Yamaha stuff.

Pads of choice are EBC HH front and EBC organic rear.

I had some Goldfren pads off eBay once. I took them off and binned them after three days. They were lethally bad. I understand that there are a lot of Goldfren knockoffs about, and many of these on eBay, so maybe these weren't representative, but it's not a risk I would take again.

I still have OE on my X after 10.5k miles (100% tarmac). Back brake is squealing a lot, despite cleaning with brake cleaner. They have around 2mm material left, but this is a guestimate - there doesn't appear to be metal/metal contact. Does the squealing indicate the pads are just about shot????

Yes! ;)

EBC 'R' Pads (they are red) if you go anywhere near dirt. Last much longer and don't fade with heavy use.

FA208 is the part number, I think, and are usually a couple of quid more than the TT pads.

The same pads are used on many other bikes.

<edit> Here's a link -> http://www.msa-direct.co.uk/ebc-brak...0z-tenere.html

Good point - As GULG suggests, if you do a good proportion of your riding off road then the R series EBC pad is probably going to work better for you than the TT.

It is probably worth clarifying that the R is sintered pad and the TT is an organic Kevlar pad.

Sintered pads last longer and work better in the wet, but chew-up/score discs up more quickly and have a more abrupt action (less �feel�). Organic pads have a more progressive �feel� and are kinder to discs, but wear a bit quicker and aren�t quite as effective in extreme conditions.

It�s horses-for-courses (bit like tyres). Choose the compound that suits your riding activity, budget and what feels right at the bars. Personal choice really; the only way you�re going to find out what suits you in the long run is to try all the different compounds/permutations.

I would agree with that... however, I've run the R pads since, erm,,, 2008ish and the rear disc hasn't suffered any undue wear, probably worth comparing with another Ten next time I'm someplace they are to see :120:

the squealing can have a number of causes. Check the pads, If they are not glazed and if they indeed still have enough meat on them there is no reason to change them. Next time you do change them you may want to clean the caliper pistons and apply a little bit of copper grease on the back of the new pads.

This is why I always use HH on the front and organic for the rear - power for one and sensitivity for the other. That's for a sporty road bike, though - I may reconsider for the XTR.

If there's no metal-to-metal contact, then squealing is most likely dust or pad vibration. If the anti-squeal shims are in place and in good condition, then a good clean and a bit of copper grease on the back of the pad as mentioned above is the answer. A smear is enough - you don't want it creeping to the braking surface.

Thanks for info on squealing!! It seems to be fairly intermittent - road salt perhaps? The pads are pretty thin, but I don't think metal/metal yet....

For the sake of �15-20 and for your own safety, you may as well change them and clean everything up while your at it. Don't wait for the backing plates to meet the disc!

Hi Phil,
i have had both EBC (the red one) and Yamaha pads. The Yamaha pads break the best and they are thicker compared to the EBC ones. The Yamaha pads have full breaking from the start. The EBC pads I had to break in. It lasted quit a while until they had their full breaking potential. And, at least in Germany, the OE pads are not much more expensive than third party pads. So I go with the OE pads.

Regards

I had some red EBC pads. A day of dirt did this to them...

http://getfile9.posterous.com/getfil...scaled1000.jpg

... to be fair, that day was the first day of the Ryedale, and *everyone* changed rear pads on the Saturday night. There's something in that Yorkshire dirt.

Strangely, I'm pretty sure the set I replaced them with are still in the bike. They were EBC as well, but gold rather than red. I don't know what that means. I think I've ordered about half a dozen pairs of rear pads from Wemoto, and they've all been different because I can never remember what I had the last time.

I run them way beyond the wear markers, although usually not quite as far as the ones in the photo. As far as I'm aware, no kittens have died as a result. Just need to check them a bit more often as they get low.

Those pads look absolutely knackered!!!!! Mine aren't anywhere near that, so I'll put up with the squealing a little longer....

Are they MX-S181 by chance ? These are gold in colour and not listed for the Tenere. They are though, listed for the TT600RE as a MotoX pad.

The TT600RE is the same caliper as the Tenere and the pads are the same part numbers - I can't see why they would list for one bike, but not for another....

I've often though about those pads, but thought they may be a little hard, needing warming up (like competition pads) - I take it they are OK for normal use then ??


Incidentally, the same pads fit many KTM's too.

These are the rear pads ive just taken out.........

http://i725.photobucket.com/albums/w...psd20f09b2.jpg

replaced them with the RED EBC ones from my local yam dealer (�17). on the back of the packet it says that the red ones are for enduro / motorcross.

Wow! Mine look like new compared to these!!!