.: XT660.com - The #1 XT660 Resource :.

.: XT660.com - The #1 XT660 Resource :. ( https://www.xt660.com/index.php)
-   Engine & Gearbox ( https://www.xt660.com/forumdisplay.php?f=206)
-   -   Rattling sound ( https://www.xt660.com/showthread.php?t=17340)

axt 23-07-11 13:57

Rattling sound
 
Hi,i have problem with rattling sound on my 2005 xtx.Sound become louder when i speed up in 5th gear from 110km/h to 150-160km/h.Also i notice,that engine has lack of power and slow acceleration.I check valve clearence and its ok.
Does anyone know what would be a problem or what shoud i look at firs?Thx

Kev 24-07-11 00:22

Quote:

Originally Posted by axt (Post 159465)
Hi,i have problem with rattling sound on my 2005 xtx.Sound become louder when i speed up in 5th gear from 110km/h to 150-160km/h.Also i notice,that engine has lack of power and slow acceleration.I check valve clearence and its ok.
Does anyone know what would be a problem or what shoud i look at firs?Thx

Does it rattle in 4th gear?

axt 24-07-11 08:37

It rattle in all gears,special in 5th.Its sound like someone is hammering the engine.
I have drive friends 05 and 08 xtx and they didnt make that sounds,also i dont get it why i cant pass 160km/h and reaching that speed is very hard,even down hill.

Kev 24-07-11 09:56

I would be taking your bike to a mechanic before something big happens, OK I see you are a mechanic, you should have the skills to diagnose the knock?

I would not ride the bike if the motor had a knock you could be causing further damage.

axt 24-07-11 11:03

Quote:

Originally Posted by Kev (Post 159510)
I would be taking your bike to a mechanic before something big happens, OK I see you are a mechanic, you should have the skills to diagnose the knock?

I would not ride the bike if the motor had a knock you could be causing further damage.

Its hard to locate exact point where sound comes,cause its transferring all over the engine,but most probably comes from the front side of the engine head(right behind water radiator).

axt 24-07-11 11:27

There is one more thing,when i check valve clearence i notice that right exhaust and right intake valves were on low side of factory specification(intake 0.09mm and exhaust 0.16mm) and left exhaust and left intake valves were on high side of specification or even more,but i didnt bother to reset valves cause were not so much out of specification(intake 0.15mm and exhaust 0.20mm).Is it possible that cam bearing is damaged.

kris007 24-07-11 13:55

Rattling sound
 
The cam has a ball bearing on each end if they were damaged you would hear a roar from the cyl head. you should try to keep the valve clerance's as close as possable whether you run them loose or tight (both ex the same & both inlet the same) check the valve and ign timing & A/F ratio (fuel map). failing that i would pull the head off and check in side for damage before it goes BANG! it will cost you lots then.

cca 24-07-11 23:02

Maybe this ?
http://www.wilddog.za.net/forum/index.php?topic=73721.0

axt 26-07-11 16:24

Quote:

Originally Posted by cca (Post 159529)

I will tray that.:icon_thumleft:

aps 26-07-11 20:06

Could it be camshaft (timing) chain tensioner? Cam chain too loose and making rattling sound.


All times are GMT +1. The time now is 12:50.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.