.: XT660.com - The #1 XT660 Resource :.

.: XT660.com - The #1 XT660 Resource :. ( https://www.xt660.com/index.php)
-   XT660Z Mods ( https://www.xt660.com/forumdisplay.php?f=165)
-   -   ToolTube Mounting ( https://www.xt660.com/showthread.php?t=14399)

Jules 12-07-10 15:36

ToolTube Mounting
 
Got these Tool Tubes (Fork Lift etc Operators manual holders) From a friend that imported a big batch to be used as tool tubes.

They are nice and sturdy and the importer had some nifty zip up baggies made that slide into each tube and keep your tools etc organized,

I used some Ally and made up some brackets to mount them to the Ten.

Works a treat, the 2 tubes carry my tools, patch kit, Gas bombs x 3, Jump Leads, Siphon hose and 1x 21" Tube, They can also carry a 750ml bottle of Scotch per tube :-)

Jules


Pics

http://home.telkomsa.net/edgepc/tenere/goosetube1.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube2.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube3.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube4.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube5.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube6.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube7.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube8.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube9.JPG

regie308 12-07-10 16:26

Nice work Jules,
I did have a similar thought to you but my idea was to mount them off the pillion peg mounts where they connect to the bike frame and then run at the same angle of the bike frame, up towards the rear grab handles.

In about 6 months keep an eye out on those pop rivets.... depending how much weight is in your tool canisters will depend on how long the rivets and alloy brackets hold up to the vibes of the bike/road surfaces. If one or the other.. or both! fail on you just..... do the same thing but in flat bar steel and nylock nuts/bolts, weight gain is minimal but stronger.

Cheers
Reg.

uncle ricky 12-07-10 18:21

Quote:

Originally Posted by Jules (Post 133163)
Got these Tool Tubes (Fork Lift etc Operators manual holders) From a friend that imported a big batch to be used as tool tubes.

They are nice and sturdy and the importer had some nifty zip up baggies made that slide into each tube and keep your tools etc organized,

I used some Ally and made up some brackets to mount them to the Ten.

Works a treat, the 2 tubes carry my tools, patch kit, Gas bombs x 3, Jump Leads, Siphon hose and 1x 21" Tube, They can also carry a 750ml bottle of Scotch per tube :-)

Jules


Pics

http://home.telkomsa.net/edgepc/tenere/goosetube1.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube2.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube3.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube4.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube5.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube6.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube7.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube8.JPG

http://home.telkomsa.net/edgepc/tenere/goosetube9.JPG


Beat me to it, I noticed that would be the ideal place to mount them.

Well done

Ni3ous 12-07-10 21:29

I did it like this:
some ordinary pipe, sealed from one side, cap on the other, one clamp to close safely the tool box...
All together costed me around 12 €.
http://www.shrani.si/t/3I/Bt/2aQQdesy/img1761.jpg
http://www.shrani.si/t/46/az/3zCZIY4G/img1759.jpg
I think it looks nice and works well. I just came from EnduRoMania and if it didnt fall of there, it will never.
http://www.shrani.si/t/1r/WI/4iIce4I5/img1760.jpg

mudmatt 13-07-10 09:54

Quote:

Originally Posted by uncle ricky (Post 133178)
Beat me to it, I noticed that would be the ideal place to mount them.

Well done

We were only talkng about that yesterday, looks good :happy3:

tdmalcolm 14-07-10 14:16

I take it with the rocket launchers you'll be staring in the next bond movie then:laughing4::laughing4::laughing4:
TDMalcolm
PS very neat job there lad

minkyhead 07-12-10 01:00

thanks for the idea
just a different take on mounting

one inch flat bar bolted accross

i just re drilled the mounting points on the tube

i figure this will be a stronger set up

welding rod for the template

and just bent the flat in a vice

http://img220.imageshack.us/img220/5983/rodqs.jpg
By minkyhead at 2010-12-06
http://img593.imageshack.us/img593/3097/rodbar.jpg
By minkyhead at
2010-12-06
http://img580.imageshack.us/img580/8683/img14620.jpg
By minkyhead at 2010-12-06
http://img530.imageshack.us/img530/851/img1467n.jpg
By minkyhead at 2010-12-06
http://img819.imageshack.us/img819/8647/img1469t.jpg

Uploaded with ImageShack.us
http://img828.imageshack.us/img828/196/rear0.jpg

Nelis 07-12-10 18:07

Looks nice.

Also the scottoiler mount behind the license plate.

tenyamman 07-12-10 22:40

if enough interest in these black tool tubes i can get these for between �12 & �14ea +P&P if enough people interested? Thats based on me buying 10 at a time & shipped from yankee land to the UK. Excludes fixings of course.!!
unless someone has got a load of them already i'd be interested in one myself.
Please feel free to PM me if looks of any interest.

Keithy 07-12-10 23:18

I had one of these on my XR http://www.bisonparts.co.uk/img/products/large/205.jpg

Cheap enough and never let any water in!

edit I forgot to disclose the source!

here they are (many suppliers of these)


All times are GMT +1. The time now is 12:50.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.